Chemineral — Petrochemicals from Oman
Chemineral
All Insights
Guide12 min read07 Nov 2026

Caustic Soda Production Routes and Purity: What Buyers Should Specify

How membrane, diaphragm and mercury-cell chlor-alkali routes shape caustic soda impurities, why end users care about different ones, and how to read a CoA and write a specification.

By Chemineral Trade Desk
Chlor-alkali plant at dusk

Two cargoes of caustic soda can both be sold as "50% liquid" and still behave very differently in your plant, because the route used to make the product decides which impurities come with it. Salt, chlorate, carbonate, iron and trace metals are the usual suspects, and each end use is sensitive to a different mix. The practical answer is to ask which production route the caustic comes from, decide which impurities matter for your process, and write those into the specification and the certificate of analysis (CoA) requirement before you agree a price.

This guide explains the chlor-alkali process at a conceptual level, how the three main routes differ, what each tends to leave behind, and how to turn that into a buying specification. It is general guidance only. It gives no numeric limits, because the right limits depend on your process, your equipment and the standard you buy to. Check the safety data sheet (SDS) and the producer's technical data sheet for the product you are actually offered.

How caustic soda is made, in one page

Almost all commercial caustic soda (sodium hydroxide) is made as a co-product of chlorine in the chlor-alkali process. A solution of common salt (brine) is passed through electrolytic cells. Electricity splits the brine into three outputs: chlorine gas at one electrode, hydrogen gas at the other, and a sodium hydroxide solution formed in the cell liquor.

The point that matters commercially is that the three products are made together. Producers are paced by chlorine demand as well as caustic demand, and caustic quality is a function of how the cell is built and how the brine is treated, not just of how the product is later finished.

Three cell designs keep the products apart in different ways:

  • Membrane cell. An ion-selective membrane separates the two sides of the cell. Only sodium ions (and a little water) cross it, so the caustic that forms is relatively free of salt.
  • Diaphragm cell. A porous diaphragm separates the two sides. The liquors can mix to some extent, so the caustic leaving the cell is a dilute solution still carrying a good deal of salt.
  • Mercury cell. Sodium is first formed as an amalgam with mercury, then reacted with water in a separate step to form caustic. The product is made directly in concentrated form and is typically low in salt.

After the cell, the liquor is usually concentrated by evaporation to the commercial strength. Strength is one decision; the route is another. For solid forms and strengths, see our caustic soda forms guide.

Laboratory bench testing chemical purity
Laboratory bench testing chemical purity

Membrane, diaphragm and mercury-cell routes compared

Answer first: membrane-cell caustic is generally the cleanest in terms of salt and the route most buyers are steering towards; diaphragm caustic generally carries more salt unless it is further purified; mercury-cell caustic is low in salt but is being phased out in many places because of the mercury.

Route General character of the caustic Typical concern for buyers
Membrane Generally low in sodium chloride and in many metals; the route most modern plants use Chlorate and iron can still vary by plant and by how the product is stored and shipped
Diaphragm Cell liquor is dilute and carries salt, so the product is generally higher in sodium chloride than membrane grade unless purified further Salt, and sometimes sulphate and chlorate; evaporation and salt removal steps matter
Mercury cell Concentrated product made directly, typically low in salt Trace mercury as a concept; production is being phased out in many places

These are generalisations. A well-run plant on one route can outperform a poorly run plant on another, and producers can add purification or filtration steps. The route tells you what to ask about; the CoA and the producer's data sheet tell you what you are getting.

Mercury-cell production is being phased out

Mercury-cell production is being phased out in many places because of concerns about mercury releases and international agreements aimed at reducing mercury use. It matters to buyers for three practical reasons:

  1. Regulation and permits. Some jurisdictions restrict or discourage imports of caustic made by the mercury route, or ask importers to declare the route. Check the position with your customs broker or regulator before you commit.
  2. Customer and sustainability requirements. Food, water and some industrial customers ask for evidence of the production route in their supply chain audits.
  3. Supply continuity. A route that is being retired is a less certain source over a multi-year contract.

If the route is not stated in the offer, ask for it. A reliable supplier will tell you; a supplier who cannot or will not name the route is giving you information too. Where you need to avoid mercury-route product, write that into the contract rather than relying on an assumption. If you buy through a trader, ask for the producer's identity and the route in writing, and have that statement carried through to the sale contract. See the key clauses guide for bulk chemicals for how origin and specification clauses are normally structured.

The impurities that matter, as concepts

You do not need to memorise every parameter on a CoA. You need to know what each impurity represents and why it might hurt you.

  • Sodium chloride (salt). Salt is the classic marker of the route and of how well the caustic was purified. High salt can cause corrosion in some equipment, can foul or crystallise in cold storage and lines, and can contaminate sensitive products. It is the first thing to compare between membrane and diaphragm product.
  • Sodium chlorate. Chlorate is a by-product of side reactions in the cell and brine system and can persist in the product. It matters for users who are sensitive to oxidising species or whose processes concentrate it over time. It is often a reason buyers ask for membrane-route product.
  • Sodium carbonate. Caustic absorbs carbon dioxide from air and forms carbonate, so carbonate can rise during storage and handling as well as being present from production. It matters because carbonate consumes alkalinity and, in some processes, builds up in recycled liquors. Poor tank breathing arrangements and long storage times raise it.
  • Iron. Iron can come from the production system but also from the tanks, pipes, tankers and drums the product has touched. Concentrated caustic can pick up iron from carbon steel, especially when hot. Iron matters where colour and staining matter.
  • Heavy metals and other trace metals. Trace metals are a concept to manage rather than a list to memorise: ask which are controlled and by what test. They matter where the caustic ends up in a product, a treated water stream or a catalytic process.
  • Sulphate and other anions. Sulphate can accumulate in some processes and is more of a concern with some routes and brine sources.
  • Mercury (mercury-cell product only). If such product is offered at all, mercury content and the route are a compliance question.

A useful frame: some impurities come from the route (salt, chlorate, mercury), some from the brine and plant (sulphate, some metals), and some from logistics (carbonate and iron picked up in tanks, pipes and storage). The third group is the one the buyer can influence most. Our storage and handling guide covers materials of construction, air exposure and temperature in more detail.

Why different industries care about different impurities

Different users run caustic through different chemistry, so the same CoA reads differently depending on who is reading it. As a general guide, with the caveat that your own process engineers know the details best:

  • Alumina refining. Caustic is used in large quantities to digest bauxite, and the liquor is recycled. Impurities that build up in a recycled liquor, such as carbonate, sulphate and chloride, cost the refinery over time. For this user, volume, consistency and the impurities that accumulate are often more important than tight limits on a single trace element.
  • Pulp and paper. Caustic is used in pulping, bleaching and chemical recovery. Impurities that accumulate in recovery systems, such as chloride, are of interest, as are metals that affect bleaching chemistry. Mills usually have their own limits and long-standing producer relationships.
  • Soap and detergents. Saponification is relatively tolerant of the bulk of impurities, but salt and carbonate affect the finished product's composition and appearance, and iron can affect colour. Cost and consistency drive most buying here.
  • Textiles and rayon. Mercerising cotton and making viscose fibre are more demanding. Iron can stain and discolour, and metals and other impurities can affect fibre quality and downstream chemistry. This is where premium grades are asked for.
  • Water treatment. Caustic is used to adjust pH and in neutralisation. Because it ends up in treated water, buyers pay attention to heavy metals and to certification for the use, which depends on the jurisdiction. If treated water is for drinking, the applicable standard and approvals matter more than a general industrial grade.

The lesson is not that one customer is fussy and another is relaxed. It is that the impurity that hurts you may not be the one on the front of the data sheet. Work out which two or three parameters your process is sensitive to and make those the centre of your specification.

Sealed caustic soda bags on pallets
Sealed caustic soda bags on pallets

Rayon or membrane grade versus standard grade

Producers and traders use grade names to signal where product sits on the purity scale. The names are not universal, so treat them as a conversation starter, not a specification.

  • Standard (or technical) grade is the general industrial product. It is fit for most bulk uses where trace levels are not critical. Depending on the producer it may come from any route.
  • Membrane grade usually signals product from membrane cells, with the lower salt and metals that implies.
  • Rayon grade usually signals tighter control of the impurities that affect viscose fibre production, notably iron and certain other trace parameters. Producers define it differently.

Three cautions apply:

  1. A label is not a spec. "Rayon grade" from one producer is not the same as "rayon grade" from another. Ask for the actual parameters and test methods behind the label.
  2. Premium grades cost more. Pay for them where your process needs them. If your use is neutralisation or general processing, you may be paying for purity you do not use.
  3. Purity can be lost after production. A premium product loaded into a dirty tank is no longer premium, so the specification should cover delivery as well as production.

If you want a particular route or grade, say so in your RFQ, and ask the trade desk what can be offered against it.

How to read a certificate of analysis

A certificate of analysis (CoA) reports test results for a specific batch or shipment. Read it the way you would read a bank statement: carefully, with a particular question in mind.

  1. Check who issued it. A CoA from the producer's laboratory is different from one from an independent inspector. For shipments where you want independent evidence, Chemineral can arrange SGS or Intertek pre-shipment inspection.
  2. Match it to the cargo. The product name, batch or tank identifier, date, quantity and vessel or container details should tie to your shipment. A generic certificate with no batch reference proves very little.
  3. Look at the strength basis. Results for impurities are reported on a stated basis, for example against the sodium hydroxide content or against the solution as a whole. Compare like with like when comparing offers.
  4. Check the parameters against your specification. Each impurity you care about should appear with a result and a test method. If one is missing, ask for it before shipment, not after discharge.
  5. Check the test methods. The method affects the result, especially at low concentrations. Where you have a method preference, say so. Do not assume that two certificates are comparable if they use different methods.
  6. Look for "typical" versus "actual". A typical analysis is an average or an indication. A batch analysis is a measurement. They are not interchangeable, and only the second is useful for a claim.
  7. Check the date. Carbonate and iron can change after production. A certificate from the production tank does not necessarily describe what is in the ship's tank after loading and a long voyage.

If the CoA looks right but the product does not perform, your recourse depends on what the contract said about sampling and testing. Our quality claims and disputes guide covers this. Agree the sampling procedure and reference laboratory before shipment; arguments over whose sample counts are hard to settle afterwards.

What to specify

A good caustic soda specification does not copy every line of a producer's data sheet. It is short, process-led and testable. Build it in this order:

  1. Product and strength. Name the product, form and strength you want. Liquid and solid products behave differently in handling, as explained in the forms guide.
  2. Production route. State the route you accept, and say explicitly if you do not accept mercury-route product. Ask for the producer's name.
  3. Critical impurities. Name the two to five parameters your process is sensitive to, with the limits you need. Limits come from your own process and your regulator, not from this guide.
  4. Test methods and basis. For each critical parameter, name the method or accept the producer's declared method, and state the basis on which results are reported.
  5. Point of quality determination. Decide whether quality is determined at load port, at discharge, or both, and who pays for the testing.
  6. Sampling and reference laboratory. Agree how samples are drawn, how many are kept and which laboratory settles a dispute.
  7. Documents. List the CoA, the independent inspection certificate if wanted, the SDS and any compliance declarations you need for your own customers or regulator.
  8. Handling and cleanliness. For tanker or ISO tank shipments, require that tanks are suitable and clean for the product, and agree how this will be evidenced.

Specify what you need, not what looks impressive. Every extra parameter you list costs money to test and creates one more way for a shipment to be argued over. Equally, do not leave your key sensitivity out because you assumed "standard" would cover it.

Common mistakes

  • Buying on strength and price alone. Two offers at the same strength can differ in salt, chlorate and metals, and price differences often reflect them.
  • Not asking for the route. The route explains much of the impurity profile and can have regulatory consequences.
  • Ignoring what happens after loading. Carbonate and iron can rise in the supply chain. Specify tank cleanliness and storage conditions.
  • Over-specifying or leaving sampling vague. A long list of parameters nobody tests properly is worse than a few well-defined ones, and an unagreed sampling procedure leaves the CoA useless in a dispute.
  • Forgetting safety. Caustic soda is corrosive and reacts strongly with some materials. Follow the SDS and your site rules for handling and emergency response; for product details see our caustic soda page.

Frequently asked questions

Which production route gives the purest caustic soda?

As a general rule, membrane-cell caustic is low in sodium chloride and is the route most modern plants use, while diaphragm product generally carries more salt unless it is further purified. Mercury-cell product is typically low in salt but is being phased out in many places. Plant operation and handling after production also affect purity, so confirm with a batch CoA.

Why do buyers ask about the production route at all?

The route explains which impurities to expect, and it can carry regulatory and customer-audit consequences, especially for mercury-cell product. Asking is a quick way to find out whether the supplier knows its own supply chain.

Is rayon grade the same as membrane grade?

Not necessarily. Membrane grade usually signals the route; rayon grade usually signals tight control of particular impurities, such as iron, for fibre production. Producers define both differently, so ask for the actual parameters and methods behind the label.

Can caustic soda get worse after it leaves the plant?

Yes. It absorbs carbon dioxide from air, which raises carbonate, and it can pick up iron from tanks, pipes and tankers. That is why the specification should cover condition at delivery as well as at production, and why tank cleanliness and storage practice matter.

Should I ask for an independent inspection certificate?

Where the cargo is large, the buyer is new to the supplier, or a letter of credit calls for independent evidence, it is usually worth it. Chemineral can arrange SGS or Intertek pre-shipment inspection. Agree the parameters and methods first so the certificate answers the questions you actually have.

Do you give numeric limits for each industry?

Not here. Limits depend on your process, equipment, regulator and the standard you buy to. Ask your process engineers or your customer for the numbers that matter, then write them into the contract.

Next step

If you are planning a caustic soda purchase and want to discuss forms, shipping and documentation for exports from Sohar or Salalah, send your requirements, including the route and impurity parameters that matter to you, via our contact page. The trade desk will respond with a firm offer, valid for 72 hours, and will quote Suez and Cape routing side by side where it affects your delivery.

Caustic SodaPurityChlor-AlkaliGuide
Trade with us
Act on this analysis.

Our trade desk can turn the views in this report into firm offers on today's indicative prices — valid 72 hours, with complete documentation.

Request a quote
Chat with our trade desk