Chemineral — Petrochemicals from Oman
Chemineral
All Insights
Logistics13 min read16 Nov 2026

Stowage Factor and Bulk Density: How Much Cargo Really Fits in a Hold, Container or Bag

What bulk density and stowage factor mean, how they decide whether a ship, container, silo or big bag fills by weight or by volume, how to do the sums, and which other properties affect loading.

By Chemineral Trade Desk
Open hold of a bulk carrier being filled with granular cargo

A buyer orders five thousand tonnes and books a vessel that can carry five thousand tonnes. The ship arrives, loads until the holds are full to the hatch coamings and sails with four thousand five hundred on board. Nothing went wrong with the weighing. The cargo was lighter per cubic metre than anyone had checked, and the ship ran out of space before it ran out of carrying capacity. The buyer pays freight on space it could not use and has to arrange another shipment for the balance.

The opposite also happens. A dense product reaches a container's weight limit when the box is only half full, and the buyer who planned by volume has ordered too much per container. Both mistakes come from the same missing number. This guide explains bulk density and stowage factor, how to use them for ships, containers, silos and bags, and what else about a cargo affects how it loads. Typical figures vary by producer, grade and condition, so use the value for your actual product, from the supplier or from measurement. For vessel freight terms, see our guide to how bulk freight is quoted.

Two numbers that say the same thing

Answer first: bulk density is how much a cubic metre of the cargo weighs. Stowage factor is how many cubic metres a tonne of the cargo occupies. One is the inverse of the other.

  • Bulk density is expressed in kilograms per cubic metre, or tonnes per cubic metre.
  • Stowage factor is expressed in cubic metres per tonne. Older documents use cubic feet per long ton, so check the units.

If a product has a bulk density of 0.8 tonnes per cubic metre, its stowage factor is 1 divided by 0.8, which is 1.25 cubic metres per tonne. Shipping people generally talk in stowage factor, and plant and packaging people talk in bulk density. They are describing the same property.

Bulk density is not particle density

A pile of granules contains air between the particles. Bulk density is the weight of the pile divided by the whole volume it occupies, air included. The density of the solid material itself is higher, and is not what you need for planning space. Polymer pellets illustrate this well. The resin's density, which appears on the data sheet and defines the grade, is the density of the solid plastic. The bulk density of a heap of pellets is much lower, because of the gaps. See our guide to HDPE, LDPE and LLDPE differences for what resin density means.

Loose and settled

Bulk density changes with how the material is handled.

  • Loose or poured bulk density is measured after gently pouring the product into a container.
  • Tapped, packed or settled bulk density is measured after vibration or tapping, when the particles have settled closer together.

A cargo settles during a voyage or a road journey, so a bag or a hold that looked full at loading has headspace on arrival. For planning space, use the loose figure, because the cargo must fit when it is poured in. For planning structural loads, such as a silo floor, the settled figure matters.

What changes it

  • Particle size and shape. Uniform, round granules pack differently from powder or flakes.
  • Size distribution. A mix of sizes packs more densely, as small particles fill gaps.
  • Moisture. Wet material can be heavier or, in some powders, fluffier.
  • Grade and process. Prilled and granular urea differ, as do ground and precipitated calcium carbonate. See prilled versus granular urea and GCC versus PCC.
  • Aeration. Freshly conveyed fine powder holds air and occupies more space until it settles.
  • Compaction under its own weight in a deep pile.

Because of this, treat a figure from a handbook as a starting point, and ask the supplier for the bulk density of the grade you are buying.

Conical stockpile under a stacking conveyor
Conical stockpile under a stacking conveyor

Weight-limited or volume-limited

Answer first: every vessel, container, truck and bag has two limits: how much weight it may carry and how much volume it holds. Whichever the cargo reaches first is the one that governs.

  • A cargo that fills the space before reaching the weight limit is volume-limited. People say it "cubes out".
  • A cargo that reaches the weight limit before filling the space is weight-limited. It "weighs out".

The break-even point is simple. Divide the usable volume by the weight limit to get the stowage factor at which both limits are reached together. A cargo with a higher stowage factor than that will cube out. One with a lower stowage factor will weigh out.

Ships

Hold capacity

A bulk carrier's capacity appears in two forms:

  • Deadweight, the total weight it can carry, from which fuel, water, stores and constants are deducted to give the cargo capacity for that voyage. Draft limits at the load port, the discharge port or along the route can reduce it further.
  • Cubic capacity, the volume of the holds. "Grain capacity" is the volume available to a free-flowing bulk cargo that fills the spaces between frames. "Bale capacity" is the smaller volume available to bagged or unitised cargo.

The sum

Cargo intake by volume equals grain capacity divided by stowage factor. Compare that with the deadweight available for cargo. The lower figure is what the ship can load.

A worked example, with invented figures for illustration only. Suppose a vessel has a grain capacity of 12,000 cubic metres and can carry 9,500 tonnes of cargo on the voyage's draft. A cargo with a stowage factor of 1.1 cubic metres per tonne would occupy 10,450 cubic metres for 9,500 tonnes, so it fits, and the ship is weight-limited. A cargo with a stowage factor of 1.4 would fill 12,000 cubic metres at about 8,570 tonnes, so the ship is full by volume with nearly a thousand tonnes of carrying capacity unused. Same ship, different cargo, different quantity.

Broken stowage and trimming

Holds are not perfect boxes, and cargo does not fill every corner. The space lost is called broken stowage, and it is larger for bagged and unitised cargo than for free-flowing bulk. Bulk cargo is also trimmed, meaning levelled, for stability and safety, and how well it can be trimmed into the ends of the hold affects the intake. Owners and brokers therefore ask for the stowage factor "as loaded", allow a margin and quote on that basis.

What to tell the broker

Give the product, form, stowage factor and its source, whether it is bulk or bagged, the bag or unit dimensions if packed, and any hazards. If you give an optimistic stowage factor and the ship cannot lift the quantity, you may owe dead freight on the shortfall. See how bulk freight is quoted and laytime and demurrage.

Bagged cargo in holds

Use bale capacity, the dimensions of the bags or units, and a realistic allowance for broken stowage. Big bags in particular leave gaps. See bagged versus bulk fertiliser shipping and choosing between bulk, container and breakbulk.

Containers

Answer first: a container has an internal volume and a maximum payload. Dense cargo hits the payload first. Light cargo fills the volume first. Road limits can cut the payload further.

A standard twenty-foot container has an internal volume of roughly thirty-three cubic metres, and a forty-foot container roughly double that, with payloads in the region of twenty-odd tonnes that do not double with the length. Exact figures vary by container, so read them from the door and the carrier's specification.

Three consequences follow:

  • Dense products, such as bagged minerals, fertilisers and drummed liquids, are weight-limited. A twenty-foot container is usually the efficient choice, because you cannot use the extra space of a forty-foot without exceeding weight limits.
  • Light products are volume-limited. A forty-foot or high-cube container carries more per box.
  • Packed cargo never achieves the product's bulk density across the whole container. Pallets, gaps between bags, headspace under the roof and the bag shape all take space. Work from the dimensions of the pallet load or big bag, not from the product's density alone.

A worked example, with invented figures for illustration only. A product in big bags measures a little over a metre square and is filled to one tonne. Twenty bags in two rows of ten fit the floor of a twenty-foot container, giving twenty tonnes of product. Add the weight of bags and pallets, and the container's tare, and compare the gross with the road limit at destination. If the road limit is lower than the container's rating, the number of bags must come down. Our guides to gross, net, tare and verified gross mass and container shipping for polymers work through the weights.

Bulk in a container, using a liner bag, behaves more like a small hold. The intake is the usable volume divided by the stowage factor, capped by the payload, with headspace needed for loading.

Row of steel storage silos at a plant
Row of steel storage silos at a plant

Big bags, silos and trucks

Big bags

A bag has a volume and a safe working load. For a given target weight, the volume you need is the weight divided by the loose bulk density, plus some headspace for closing. A bag sized for a dense fertiliser will be too small for the same weight of a light powder, and a bag sized for a light product will be half empty and unstable with a dense one. Give the bag supplier your bulk density. See our guide to big bags.

Silos and bins

Silo capacity is quoted in cubic metres, and sometimes in tonnes of a reference product. Tonnage for your product equals volume times bulk density. The usable volume is less than the geometric volume, because of the cone at the top formed by the angle of repose, and the material that remains in the bottom depending on the outlet design. Structural loads should be checked against the settled density.

Warehouses and floors

Floor loading matters for stacked bags and bulk piles. A pile's footprint and height depend on the angle of repose, which fixes how many tonnes fit in a bay. See urea storage and caking for pile management.

Trucks

Bulk trucks and tippers have a body volume and a legal payload. Dense cargo reaches the legal weight with space to spare. Light cargo fills the body under the weight limit. Plan the number of trucks from whichever applies.

Other properties that affect loading

Angle of repose

When a granular material is poured, it forms a cone. The angle between the slope and the horizontal is the angle of repose. A low angle means the material flows freely and spreads out. A high angle means it heaps steeply and may need trimming. For ships, the angle of repose also matters for stability, since free-flowing cargoes can shift. For storage, it sets the shape of a pile and the capacity of a bay or silo.

Flow behaviour

Cohesive powders bridge over outlets and hang up in corners, so a container or silo may not empty fully, and a hold may need more trimming. Moisture, particle size and time under pressure all make it worse. Caked product does not flow at all.

Moisture and the safety rules for bulk cargo

Solid bulk cargoes carried by sea are governed by international safety rules that group cargoes by the hazards they present, such as cargoes that may liquefy when their moisture content is too high, cargoes with chemical hazards and cargoes with neither. Shippers must give the master a declaration with the cargo's properties before loading. Which group a product falls into, and what tests or certificates are required, is a matter for the shipper, the surveyor and the master under those rules. Ask your supplier and forwarder how your product is declared. See dangerous goods in shipping chemicals and the safety guidance in sulphur dust and fire safety.

Settling and compaction

Cargo settles in transit, so volumes at arrival are lower than at loading. This is why a full bag looks slack later, and why weight, not volume, is the basis for trade. For how weight is determined, see our draft survey guide.

Liquids

Liquids are planned by density and temperature. Tanks are never filled completely, because space, known as ullage, is left for the liquid to expand as it warms. Density changes with temperature, so the same weight occupies more volume when hot. This matters for heated cargoes such as bitumen, and for base oil. See bitumen heating, storage and handling and base oil specifications.

Measuring bulk density yourself

Answer first: a simple check takes ten minutes and a known container.

  1. Take a rigid container of known volume, such as a calibrated bucket or measuring box. The larger it is, the better for coarse products.
  2. Weigh it empty.
  3. Pour the product in gently from a low height until it overflows, without shaking.
  4. Level the top with a straight edge.
  5. Weigh it full.
  6. Subtract the empty weight and divide by the volume. That is the loose bulk density.
  7. For a settled figure, tap or vibrate the container, top it up, level and weigh again.
  8. Repeat three times and average.

Laboratory methods exist for more precise work, and the supplier's data sheet may quote a value with its method. Use a representative sample, since fines and coarse fractions have different densities.

What to ask the supplier

  1. Loose bulk density of the grade, and the settled figure if known.
  2. The stowage factor used for previous shipments, bulk or bagged.
  3. Angle of repose and any flow or caking issues.
  4. Bag, pallet or big-bag dimensions and filled weights.
  5. A loading plan for the container or vessel, with weights and volumes.
  6. How the cargo is declared under the bulk cargo safety rules, if shipped in bulk.
  7. Any moisture limits relevant to shipping.
  8. Whether density varies between lots or seasons.

Chemineral ships from Sohar and Salalah, and the trade desk can provide packing dimensions and a loading plan with an offer.

Common mistakes

  • Planning a vessel on deadweight alone, without checking cubic capacity.
  • Using particle density when bulk density was needed.
  • Mixing units, such as cubic feet per long ton and cubic metres per tonne.
  • Assuming packed cargo fills a container to the product's bulk density.
  • Ignoring road limits on container weight.
  • Ordering big bags by weight without giving the bulk density.
  • Using a handbook figure for a different grade or form.
  • Forgetting settling, then disputing "missing" volume.
  • Giving an optimistic stowage factor and paying dead freight.
  • Overlooking the declaration required for solid bulk cargo.

Frequently asked questions

What is stowage factor?

It is the volume occupied by one tonne of a cargo, usually in cubic metres per tonne. It is the inverse of bulk density and is used to work out how much cargo fits in a ship's hold.

What is the difference between bulk density and density?

Density is the mass of the solid material per unit volume. Bulk density is the mass of a pile of the material divided by the volume it occupies, including the air gaps between particles. Bulk density is always lower.

Why did my ship load less than its deadweight?

Probably because the cargo filled the holds by volume before reaching the weight limit. That happens when the stowage factor is higher than the ship's break-even figure. Draft restrictions can also reduce the cargo.

How do I know whether a container will be weight-limited or volume-limited?

Divide the container's usable volume by its permitted payload. If your cargo's stowage factor, as packed, is lower than that figure, weight governs. If it is higher, volume governs.

Does bulk density change during transport?

Yes. Vibration settles the cargo, so it occupies less volume on arrival. The weight does not change, apart from moisture gain or loss.

Next step

If you want a loading plan for a container or a bulk parcel, send the trade desk your product, packing, quantity and destination through the contact page. We quote Suez and Cape routing side by side for shipments from Sohar and Salalah, and firm offers are valid for 72 hours.

Stowage FactorBulk DensityShippingLogisticsPlanningGuide
Trade with us
Act on this analysis.

Our trade desk can turn the views in this report into firm offers on today's indicative prices — valid 72 hours, with complete documentation.

Request a quote
Chat with our trade desk